This inspection checklist is a planning aid, not a substitute for a site evaluation, engineering opinion, permit review, or written estimate. For septic-system background, consult the U.S. Environmental Protection Agency septic resources. For business-planning and contractor-management resources, consult the U.S. Small Business Administration. Confirm requirements, availability, and pricing with your local health department, utility, permitting office, and qualified contractors.
When a buried sewer, septic, stormwater, or other private service line is damaged, three common repair approaches may appear in a contractor’s proposal: a spot repair, cured-in-place or similar lining, and open-cut excavation with replacement. Each method can be reasonable in the right conditions. The best choice depends on the condition of the entire line, the location of the defect, access, soil, groundwater, connected structures, and local requirements.
This checklist is designed for comparing the three options over the same measured length. It does not assign a universal rate. Local labor, equipment, materials, disposal, restoration, permitting, and site conditions vary too widely for a reliable national price. Ask each contractor to price the same linear footage, define the same scope, and identify exclusions. Then confirm the proposal with local professionals and the appropriate authority before work begins.
What should be confirmed before comparing repair methods?
Start by confirming what line is being evaluated. Identify whether it serves a building drain, private sewer lateral, septic tank, distribution line, storm drain, foundation drain, or another system. The repair method, inspection standards, and approval process may differ.
- Record the address and the line’s apparent purpose.
- Locate cleanouts, tanks, pump components, manholes, easements, and property boundaries.
- Measure or estimate the affected length and record the measurement method.
- Collect any available plans, prior repair records, maintenance records, and inspection videos.
- Ask who owns and maintains each segment of the line.
Do not assume that the visible symptom identifies the damaged section. A backup, odor, wet area, slow drain, or surface depression may have more than one cause.
Has the line been inspected from end to end?
Request a camera inspection where the line can safely be accessed. The report should identify the starting point, ending point, direction of travel, pipe diameter, material if known, depth if known, and the location of each defect. A useful report distinguishes a single localized failure from recurring defects along the line.
Ask for video or still images that show the defect clearly. The written report should describe cracks, open joints, offset joints, corrosion, root intrusion, collapsed sections, sediment, grease, standing water, separations, and evidence of infiltration or exfiltration. If the camera cannot pass, ask why. A blockage or collapse may prevent a complete inspection and can change the recommended repair.
Is the measured length identical in all three proposals?
For a fair comparison, require one common quantity. Call it L, the confirmed repair length in linear feet. Each proposal should use the same L, unless a contractor explains why the method requires a different length and provides an alternate comparison.
| Method | Measured length | Quoted price | Required scope description |
|---|---|---|---|
| Spot repair | L linear feet, with exact repair points | Local written quote: $_____ | Excavation or access, repair, testing, backfill, and restoration |
| Lining | L linear feet, from stated access points | Local written quote: $_____ | Cleaning, preparation, liner installation, curing, reconnection, and testing |
| Open cut | L linear feet, along the stated trench route | Local written quote: $_____ | Excavation, replacement, bedding, backfill, compaction, and restoration |
Do not compare a spot-repair price that excludes restoration with a lining price that includes cleaning and reconnections. Ask for a written scope before comparing totals.
When is a spot repair a reasonable option?
A spot repair may fit a line with one clearly located and accessible defect while the surrounding pipe remains serviceable. It can involve exposing a limited area, removing the failed section, installing a replacement segment, reconnecting the pipe, testing it, and restoring the surface.
Ask the contractor to identify why the repair is considered localized. The inspection should support the conclusion that nearby joints, walls, and transitions do not show similar failure. A spot repair may be less attractive if the line has repeated offsets, widespread cracking, significant corrosion, multiple root intrusions, or poor alignment beyond the proposed excavation.
Confirm whether the quote includes locating the defect, traffic or pedestrian control, shoring or trench safety measures, groundwater handling, disposal, surface restoration, and reconnection of branches. A small repair area does not automatically mean a small project. Depth, access, pavement, landscaping, utilities, and groundwater can dominate the work.
When might lining be technically suitable?
Lining generally depends on an existing host pipe that can accept the liner and remain sufficiently stable during preparation and installation. The contractor should explain the proposed lining process, access points, cleaning method, curing method, expected finished inside diameter, and how service connections will be reopened.
Ask whether the liner can address the specific defects shown in the inspection. A liner may not be appropriate where the host pipe is severely collapsed, badly misaligned, missing, inaccessible, or unable to support installation. The contractor should also explain how bends, transitions, laterals, diameter changes, and active water infiltration will be handled.
Request product and installation information suitable for your local project. Ask who will perform the work, what inspection occurs after curing, how curing is documented, and what warranty terms apply. Do not treat a warranty as proof that the method is suitable. The pipe condition and installation quality still require evaluation.
When is open-cut replacement worth evaluating?
Open-cut replacement exposes the line so the damaged pipe and surrounding conditions can be addressed directly. It may be appropriate when the pipe has collapsed, has repeated failures, has poor slope or alignment, is difficult to access for lining, or needs a change in route or depth.
The inspection checklist should include trench route, depth, soil conditions, nearby structures, trees, utilities, pavement, retaining features, groundwater, and access for equipment. Ask how excavated material will be handled and whether imported bedding or backfill is included.
Open-cut work can provide direct visibility, but restoration may be extensive. Require separate descriptions for pavement, concrete, pavers, lawns, planting beds, fencing, irrigation, and other affected features. Confirm who is responsible for temporary protection and final restoration.
What site conditions could change the recommendation?
Walk the proposed work area with the contractor when possible. Record conditions that may affect feasibility or cost, including:
- Limited equipment access or narrow gates.
- Driveways, sidewalks, roads, walls, decks, buildings, and other hardscape.
- Private and public utilities near the route.
- High groundwater, saturated soil, flooding, or unstable soil.
- Large roots, protected trees, landscaping, or environmental sensitivities.
- Shared lines, easements, neighboring property, or unclear ownership.
- Building occupancy, temporary service interruptions, or bypass needs.
Ask each bidder to list assumptions. A proposal based on easy access should not be treated as equivalent to one that includes difficult excavation or bypass pumping.
What should the inspection report document?
A useful report connects findings to recommendations. It should include the inspection date, equipment used, line access points, pipe size, observed material, defect locations, distances from the camera entry point, and limitations. Photos, video, sketches, and a site map can reduce disputes.
Ask the inspector to classify each defect by location and apparent significance. For example, distinguish a root intrusion from a fractured pipe, and a minor joint opening from a full collapse. The report should state whether the camera reached the full intended length. If not, explain what prevented completion and what additional work may be needed.
Keep the original video and written report. Provide the same information to all bidders so the proposals are based on comparable evidence.
Are permits, approvals, and utility checks required locally?
Confirm local requirements before accepting a proposal. Depending on the system and location, the work may involve a health department, building or plumbing office, public works department, road authority, environmental office, utility owner, or property association. Septic work can have requirements that differ from private sewer or stormwater work.
Ask who will obtain permits, schedule inspections, contact utility-locate services, and pay application or inspection charges. Do not assume these items are included. Verify the answer with the relevant local office rather than relying only on a contractor’s verbal statement.
If the line crosses a property boundary, easement, public right of way, or shared access area, confirm authorization before excavation or lining. Keep written records of approvals and conditions.
What should every price include?
Request an itemized proposal for the same L linear feet. Each price should identify included work and excluded work. At minimum, ask about:
- Inspection, locating, cleaning, and preparation.
- Labor, materials, equipment, mobilization, and supervision.
- Access pits, excavation, shoring, trench protection, or bypass service.
- Water handling, disposal, hauling, and imported material.
- Connections, fittings, transitions, cleanouts, and testing.
- Permits, inspections, utility coordination, and traffic control.
- Backfill, compaction, temporary protection, and final restoration.
- Taxes, allowances, warranty terms, and change-order procedures.
If a contractor cannot price an uncertain item, request an allowance with a clear basis and a written approval process. Avoid comparing a firm total with an unexplained allowance.
How can the three prices be compared fairly?
Use a comparison sheet that separates base work from optional or uncertain work. The three prices should be labeled with the same measurement, access assumptions, restoration standard, testing requirement, and completion conditions.
| Question | Spot repair | Lining | Open cut |
|---|---|---|---|
| Same measured length? | Yes / No | Yes / No | Yes / No |
| Same testing and inspection? | Yes / No | Yes / No | Yes / No |
| Restoration included? | Details: _____ | Details: _____ | Details: _____ |
| Known exclusions? | _____ | _____ | _____ |
The lowest initial price may not represent the lowest total project cost if it excludes access, restoration, reconnections, or future repairs. Compare technical fit and scope first, then compare price.
What questions should be asked about contractor qualifications?
Ask for the business name, contact information, applicable local license or registration details, insurance confirmation, and references for similar work. Verify information through appropriate local or professional channels. Do not rely on unsupported claims, generic ratings, or pressure to sign immediately.
Ask who will inspect the line, who will perform the repair, who will supervise the work, and who will handle warranty requests. For lining, ask about installer training and the specific process proposed. For excavation, ask about trench safety planning and utility coordination. For all methods, ask how changes will be documented and approved.
What safety and service-continuity issues should be planned?
Keep occupants, visitors, pets, and unauthorized workers away from open excavations, equipment, contaminated water, and exposed pipe. Ask the contractor to explain access control, temporary covers, work hours, and emergency contact procedures.
Confirm whether the building or system will be unavailable during cleaning, repair, curing, reconnection, or testing. Ask whether temporary bypass, alternate facilities, or staged work is required. Do not enter a tank, trench, manhole, or confined space unless the work is being performed by properly trained and equipped professionals.
What should be documented before work begins?
Before signing, assemble the inspection video, written findings, site photos, measurement, selected scope, permits or approvals, insurance information, proposal, schedule, payment terms, warranty, and change-order procedure. Mark the agreed repair length and access points on a sketch.
Photograph existing pavement, landscaping, structures, fences, irrigation, and other features that could be affected. Ask how preexisting damage will be recorded. Confirm the restoration standard in writing, including materials, approximate finish, grading, and cleanup.
How should the final repair be verified?
Require final testing appropriate to the system and method. Ask for a post-repair camera inspection where practical, along with confirmation that connections are open, flow is restored, and the work matches the approved scope. For lining, request documentation of installation and curing. For open cut or spot repair, request confirmation of bedding, backfill, compaction, and surface restoration when those items apply.
Keep final photos, test results, invoices, permits, warranty documents, and updated sketches. If the result does not match the proposal, document the issue promptly and request a written response.
What is the final decision checklist?
- Confirm the line type, ownership, and affected location.
- Obtain the most complete feasible inspection and preserve the records.
- Measure one repair length, identified as L.
- Request spot repair, lining, and open-cut proposals for the same L.
- Require each proposal to state assumptions, exclusions, restoration, testing, and warranty terms.
- Confirm permits, utility coordination, easements, and local approvals.
- Compare technical suitability before comparing price.
- Get changes and allowances in writing.
- Verify contractor qualifications and insurance locally.
- Document the completed work and retain final records.
The right choice is the method that addresses the documented failure, fits the existing line and site, meets local requirements, and provides a clear scope for the same measured length. Confirm all three prices locally, because actual project costs depend on conditions that cannot be established from a general checklist alone.